Climax Part RC-037 Mild Steel, Black Oxide Plating, άκαμπτος σύνδεσμος, οπή 3/8 ιντσών, OD 3/4 ιντσών, Μήκος 1 ίντσας, 1/4-20 x 3/16 ρυθμιστική βίδα

Brand:Climax Metals

3.5/5

44.21

RC037, ΕΤΑΙΡΙΑ ΜΕΤΑΛΛΙΚΑ ΠΡΟΪΟΝΤΑ CLIMAX, 3/8^ ΣΥΝΔΕΣΗ ΡΑΔΙΩΝ ΜΕ ΣΕΤ

Δεν υπάρχουν διαθέσιμες μονάδες
Το μαύρο οξείδιο παρέχει κάποια αντίσταση στη διάβρωση. Ανοχή: +.0005/+.0025. Τοποθετείται εύκολα όπου διαφορετικά θα απαιτούνταν μεγάλη αποσυναρμολόγηση. Οικονομικός σχεδιασμός ζεύξης. Παρέχει μετάδοση και ευθυγράμμιση ροπής.
Country of Origin USA
Item model number RC-037
Manufacturer Climax Metal Products Company
Package Dimensions 5.91 x 3.9 x 0.98 inches; 0.32 Ounces

3.5

8 Review
5 Star
69
4 Star
17
3 Star
9
2 Star
2
1 Star
2

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: redtreetoad
Set screws have sloppy tolerance
For a while I thought that the set screws used a odd size hex key that I didn’t have. After going through all my metric and SAE hex keys (I have about 100 hex keys of various sizes), the closest fit was a 1/8” hex key. I tried 5 different 1/8” hex keys to tighten the set screws, and all of them were a tad too small for the set screw hex holes. You can tighten the set screws to a decent amount, but if you want to really crank them down, the hex key will undoubtedly slip and strip the set screw or the hex key. I measured the bore of the coupling with my Starrett calipers, and it read 0.3745” (within 5 mills of 3/8”), so other than the set screw issue, it fits just fine on my stepper motor’s 3/8” shaft.
Scritto da: Dennis Mountains
Works great
I have a 3/8" round D shaft on the motor connected to a 3/8" threaded rod. This coupler holds tight on both the motor shaft and the threaded rod.
Scritto da: Melissa Miller
could use improvement
The set screws do not bite into the rod well and pulls off. I replaced with bolts and it works.
Scritto da: Dean Winters
Does it’s job
Worked perfectly. Needed to swap out the engine on my old ariens snowblower, and the new engine interfered with the shaft used to move the throw chute. Used it to add an extension into the shaft before the universal joint and works perfectly.
Scritto da: SPM II
Good quality
Product fit perfect, I had to extend a 3/8 shaft for a snowblower chute crank rod
Scritto da: Kayak Jay
Dimensions on the Money
This connector worked great to join two pieces of an axle.
Scritto da: Dubs
It worked for me
Not the highest quality but it did what I needed it to do. I used it to connect my rotisserie to the motor shaft. So a high quality part was not required
Scritto da: Bill Warner
Three Stars
didn't end up using.

Σχετικά προϊόντα

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array