Superior Electric L50 Aftermarket Trigger Switch 24/12A-125/250V συμβατός με Makita 651172-0, 651121-7 και 651168-1, κόκκινο

Brand:Superior Electric

3.1/5

51.45

Το Superior Electric L50 Aftermarket Trigger Switch αντικαθιστά το Makita 651172-0. Αυτός ο διακόπτης μπορεί να βρεθεί σε πολλά δισκοπρίονα και μύλοι Makita. Οι διακόπτες είναι συνήθως ανταλλακτικά στα ηλεκτρικά εργαλεία. Ένας διακόπτης χειρίζεται όλες τις λειτουργίες on/off και μεταβλητής ταχύτητας. Έχουν επίσης ρόλο στο ηλεκτρικό σπάσιμο. μπορούν να αντιστρέψουν στιγμιαία την ηλεκτρική πολικότητα. Επειδή οι διακόπτες χρησιμοποιούν μηχανικά εσωτερικά, τείνουν να υποβαθμίζονται και να φθείρονται με την πάροδο του χρόνου, απαιτώντας τελικά αντικατάσταση. Αυτός ο διακόπτης αποδεικνύεται ότι είναι μια άξια αντικατάσταση με κορυφαία ποιότητα και χαμηλότερη τιμή. ΣΗΜΕΙΩΣΗ: Μερικά κοινά σημάδια ενός σπασμένου ή αποτυχημένου διακόπτη είναι: Το εργαλείο έχει σταματήσει τελείως να λειτουργεί - δεν ενεργοποιείται Το εργαλείο λειτουργεί κατά διαστήματα, απαιτούνται πολλαπλές προσπάθειες για ενεργοποίηση, έως ότου τελικά δεν θα ενεργοποιηθεί καθόλου Λειτουργία μεταβλητής ταχύτητας και ηλεκτρική η πέδηση δεν λειτουργεί σωστά Αυτό το εξάρτημα είναι συμβατό με: Makita: 5007S Δισκοπρίονο, 5007NB Δισκοπρίονο, 5008NB Δισκοπρίονο, 5007FK Δισκοπρίονο, 5007NBK Τύπος 1 7-1/4 Basic 15Gavy06Aluminium 0. 5A 6 Cutoff / Angle Grinder, GA5010Z 10. 5A 5 Angle Grinder, 5057KB 7-1/4 Diircular Saw, 5007F 7-1/4 Diircular Saw with Brake, GA5010, GA6010.

Δεν υπάρχουν διαθέσιμες μονάδες
✅ Ένταση: 24A/12A. ✅Τάση: 125/250V. ✅ Η λειτουργία μεταβλητής ταχύτητας και το ηλεκτρικό φρενάρισμα δεν λειτουργούν σωστά. ✅ Το εργαλείο λειτουργεί κατά διαστήματα, απαιτώντας πολλαπλές προσπάθειες για να ενεργοποιηθεί, έως ότου τελικά δεν θα ενεργοποιηθεί καθόλου. ✅ Το εργαλείο έχει σταματήσει εντελώς να λειτουργεί - δεν θα ανάψει. ✅ ΣΗΜΕΙΩΣΗ: Μερικά κοινά σημάδια ενός σπασμένου ή βλάβης διακόπτη είναι:.
Batteries ‎1 Lithium Ion batteries required.
Batteries Included? ‎No
Batteries Required? ‎No
Brand Superior Electric
Brand ‎Superior Electric
Color Red
Color ‎Red
Customer Reviews 4.0 4.0 out of 5 stars 458 ratings 4.0 out of 5 stars
Included Components ‎Power tool Replacement part
International Protection Rating IP541
International Protection Rating ‎IP541
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 1 x 1 x 1 inches
Item Dimensions LxWxH ‎1 x 1 x 1 inches
Item model number ‎L50
Item Package Quantity ‎1
Item Weight ‎1.44 ounces
Manufacturer ‎Superior Electric
Measurement System ‎Imperial
Number of Items 1
Number of Items ‎1
Operating Voltage 250 Volts
Operating Voltage ‎250 Volts
Operation Mode ON-OFF
Operation Mode ‎ON-OFF
Part Number ‎L50
Power Source ‎Corded Electric
Product Dimensions ‎1 x 1 x 1 inches
Unit Count 1.0 Count
Unit Count ‎1.0 Count

3.1

13 Review
5 Star
59
4 Star
15
3 Star
10
2 Star
2
1 Star
14

Γράψτε την κριτική σας

Το email σας δεν θα δημοσιευτεί. Όλα τα υποχρεωτικά πεδία επισημαίνονται με*

Scritto da: Oliver M
wish the input outputs would be better labeled
installed this on an old black and decker professional chop saw. i was surprised it was a direct fit. i was however surprised to see that the power is interrupted between adjacent terminals. no big deal but would of made initial install a bit quicker to know that. older switch interrupted across length wise
Scritto da: Lindsey
Fit our rigid saw. Sorta
Good freaking luck finding a switch for a rigid saw. The TYCO ones are non existent. This was shaped exactly like the old one. Only issue is it's 4 terminal vs 3. It does not do the power switching as the old one did for saw blade brake. Otherwise it fit great! Deducted a star as there is no diagram on the exterior. That would have been clutch.
Scritto da: Douglas A. Learn
good switch but not a direct replacement
This switch will fit the saw I bought it for but the wireing has to be swapped around to make it work, Make sure you ohm out the contacts before installing. would have been helpful had they put numbers on the switch so you would know how to wire it up .
Scritto da: knute
Good Deal If You Don't Mind Fiddling
Appears to be a high quality switch, but not a direct replacement for the switch on a 5007F Makita Circular Saw. While this replacement switch is approximately the same size as the original, the part that makes the magic happen is larger. There is also a reinforcement in the trigger bar that will not allow it to fit in the saw handle. In the pics you can see the portion I cut out of the switch so it would fit in the handle. Note that the instructions ARE correct. In the photo, the two white wires are from the source, the two black wires are the load. That IS different than the way the original is wired. The pics illustrate the correct wiring. I had enough wire to make the change without modifications, but you will have to bend the two contact wires closest to the trigger. That said, once installed, works great. I have two of these saws (left for dead by a contractor) and they both now work perfectly. If you don't mind a little fitment, good purchase. Or perhaps it works fine with your 5007
Scritto da: Eric Froese
TAKE NOTE OF DIAGRAM ON SWITCH!
Take note of the diagram on this switch (HY38)! The contact between the two terminals on each END of the switch is closed when the trigger is pulled. The two ENDS are separate from each other. So, you should connect one line wire and one load wire on each end. (For example, the white wire from the power cord and white wire going to the motor should be connected to two terminals on the same end.) This is different from the factory switch on my Makita GA 6010 angle grinder, where the two SIDES are separate from each other, and the contact between the two terminals on each SIDE is closed when the trigger is pulled. If I connected the wires to this switch the same as they are connected to the Makita factory switch, I would short the power supply when I pulled the trigger!
Scritto da: coop
Worked out fine
Little modification worked on old hd77 worm drive saw .
Scritto da: Joe Bouler
Did not fit my Makita saw
My old switch didn't have a part number so I had to go by the pictures. This switch looked like what I had so I bought it. When I tried to install it, it was too thick to fit in my saw. I filed some of the plastic off the new switch without damaging it and was able to make it fit. The wiring configuration is completely different from the original switch but I installed it according to the numbers on the terminal screws. After getting everything back together my saw didn't work. With the old switch, the saw would run as soon as to plugged it in. It wouldn't turn off which was very dangerous. I put the old switch back in the saw and it still doesn't work. Apparently I messed up something while installing the switch.
Scritto da: Tony
Not for late model Makita 5007F
Not for late model Makita 5007F already tried.. all it does is bump the breaker.....
Scritto da: Bryn E.
Switch is great with 1 minor CAUTION Notice
! Switch pin out different from original 8638k2 Switch ! Switch has good positive switching action and fits right into my Early 80's 5007NB. Only one small issue and it is more of a beware and you will NOT have an issue. The new switch terminals have a different pin out from the ORIGINAL "C-H" branded 8638K2 switch that was installed in the saw. Original pin out: Trigger load 1 2 1 2 Line New switch: Trigger L/L 1 1 2 2 L/L
Scritto da: Richard Garnett
Does not fit what the say it fits
Was advertised to fit a makita 5007f skill saw. You would have to modify the handle for this to fit. Did not want to do that a saw that was only 1 year old
Scritto da: SPR Locks
Excellent customer service!
Switch quality was excellent but unfortunately I was not able to make it fit in my tool as a replacement. The seller offered amazing response time and granted a refund right away. Excellent company and customer service experience.
Scritto da: jean bedard
Patience avec poste Canada c’est très long
Enfin arrivé COVID oblige, la poste est très lente, près de 1 mois de retard . Service après-vente impeccable. La switch est parfaite
Scritto da: CHIA TING PAN
Great quality
Great quality, great product, well done!

Σχετικά προϊόντα

hot
Blakeslee 17514, Impeller Spindle
0.1/5

€ 331.82

Blakeslee 17514, Impeller Spindle
0.1/5

€ 331.82

Ανακαλύψτε το διεθνές μας δίκτυο

Στέλνουμε σε 28 χώρες, πάνω από 200.000 προϊόντα. Μείνετε ενημερωμένοι, εγγραφείτε στο ενημερωτικό δελτίο.

Array